#ZOIPER SIP 408 REQUEST TIMEOUT HOW TO#
#ZOIPER SIP 408 REQUEST TIMEOUT FULL#
#ZOIPER SIP 408 REQUEST TIMEOUT MAC#

I found a work around for this problem by deleting the blank lines when the config file changes.įor this we have to make the below change in asteisk-gui file “/var/lib/asterisk/static-http/config/js/index.js”. of the blank lines increases with configuration changes and after certain no of changes the the asterisk pbx stop responding and it could not read the config files because of the huge file size. When I installed the Asterisk-GUI., I found that once we make any changes in configuration from i asterisk-gui, it will insert many blank lines along with the changes in the configuration files(/etc/asterisk/*.conf).

This is a list of the known SIP status codesĦ05 – Not Acceptable Posted in Technical Tagged Asterisk, Asterisk Dubai UAE, Freepbx VoIP UAE, IP Phones Dubai, SIP, Technical, VOIP, VoIP Dubai Delete Blank lines from Asterisk Config files , then it will show the SIP profile “Registered”. Public username: your need to put “sip: ” it will pre append automatically) Use this to select your access point SSID which your are connected(Your router’s Wireless connection’s name). settings -> SIP settingsįrom the options select ” New sip profile” On your phone and goto Menu -> Settings->connectivity->Admin. I could successfully configure actionvoip with E6.

#ZOIPER SIP 408 REQUEST TIMEOUT HOW TO#

Via: SIP/2.0/UDP 192.168.33.1:5063 rport=5063 received=192.168.33.Here I brifely describes how to configure nokia E6 with a voip provider. NOTICE: res_pjsip/pjsip_distributor.c:676 log_failed_request: Request 'REGISTER' from '' failed for '192.168.33.1:5063' (callid: _R51m7KNwSEepDSdZ6NrSA.) - Failed to authenticate NOTICE: res_pjsip/pjsip_distributor.c:676 log_failed_request: Request 'REGISTER' from '' failed for '192.168.33.1:5063' (callid: _R51m7KNwSEepDSdZ6NrSA.) - No matching endpoint found Instead of Request Timeout (code: 408) error, I now get Unauthorized (code: 401) and I see this in the Asterisk logs: I changed all the references to 127.0.0.1 to 192.168.33.10 in dev.env, so the Elixir project works fine.

I then tried running the Asterisk container inside an Ubuntu virtual machine, using -net host, and running it on a bridged network (VM had IP 192.168.33.10).

On the accounts page it says Request Timeout (code: 408) and there is nothing in the Asterisk logs.

However, I was unable to connect to Asterisk with Zoiper.

After this, I could start the project with iex -S mix and it connected!

#ZOIPER SIP 408 REQUEST TIMEOUT MAC#

command uses -net host, which doesn’t work on Mac unfortunately. I haven’t played with Asterisk before so I’m not really sure what’s going wrong. So I wanted to try the ex_ari_example out last night, but I had some trouble with the Asterisk part. The documentation is pretty thorough, but it definitely helps to understand Asterisk and ARI.Īnd on hex.pm Brought to you by CityBase If you’re not to familiar with Asterisk, there’s an example repo that will get you up and running with a custom Asterisk IVR in a few minutes.

#ZOIPER SIP 408 REQUEST TIMEOUT FULL#

This library has full support for both the REST and Websocket protocols. ARI also provides a Websocket interface for consuming events from the Asterisk Server. Through the REST interface it is possible to control just about every aspect of an Asterisk server. It has been thoroughly tested with Asterisk versions 15 and 16.ĪRI stands for Asterisk REST Interface. The ARI protocol is a robust interface for controlling Asterisk and reacting to Asterisk events. An Elixir library for interfacing with Asterisk using the ARI protocol.īe sure to check out the example application

Zoiper sip 408 request timeout